For a long time, the most common steel grade used in truck gears in my country is 20CrMnTi. This is a medium-sized 18XTr steel grade (ie 20CrMnTi steel) for automobile gears imported from the former Soviet Union in the 1950s. The steel has fine grains, has a small tendency to grow grains during carburization, and has good carburizing and quenching performance. It can be quenched directly after carburizing. The literature pointed out that before 1980, my country's carburized alloy structural steel (including 20CrbinTi steel) only guaranteed the chemical composition of the steel and the mechanical properties measured with samples when the steel was delivered. However, the chemical composition and mechanical properties often appeared in the production of automobiles. Qualified steel, due to the excessive fluctuation range of hardenability, which affects the quality of the product. For example, if the hardenability of 20CrMnTi carburized steel is too low, the core hardness of the gear after carburizing and quenching will be lower than the value specified in the technical conditions, and the fatigue life of the gear will be reduced by half during the fatigue test; if the hardenability is too high If the gear is high, the shrinkage of the inner hole of the gear after carburizing and quenching is too large, which will affect the gear assembly.
Because the hardenability of steel has an extremely significant impact on the hardness and distortion of the tooth core, the Ministry of Metallurgy issued my country's technical conditions for guaranteed hardenability structural steel (GB5216-85) in 1985, which was included in this technical condition The chemical composition and hardenability data of 10 carburizing steels including 20CxMnTiH and 20MnVBH steels are presented. The standard stipulates that the hardenability index of 20CrMnTi steel used to manufacture gears is 30-42HRC at a point 9 bar away from the water-cooled end. After that, the problem of too low hardness and too large distortion in the tooth core of the gear produced by using 20CrMnTi steel was basically solved. However, it is obviously unreasonable to use the same steel grade 20CrMnTi regardless of the size of the gear module and the thickness of the steel section. Due to the improvement of the level of steel smelting technology in my country and the improvement of the supply of alloy structural steel, there are conditions to further narrow the hardenability band of gear steel and develop it according to the requirements of different products (such as transmission gears and rear axle gears, etc.) The new steel grade meets its requirements.
Through negotiation with steel mills, in 1997, Changchun FAW signed agreements with gear steel manufacturers to supply the hardenability of 20CrMnTi steel in different stages. The hardenability groups of 20CrMnTiH steel used for the primary and secondary gears of the small transmission and the larger section size of the rear axle main and driven bevel gears are I and II, and the corresponding hardenability groups are J9: 30—36HRC and J9=36-42HRC.
Around 1960, due to the tight supply of nickel and chromium steel in China, the production of nickel and chromium-containing steel in my country was affected. At that time, my country's automobile industry was based on technology imported from the former Soviet Union, and the Soviet Union used a large number of nickel and chromium-containing steels. Therefore, at that time, my country's automobile industry vigorously developed the development and research work of boron steel, using 20MnVB and 20Mn2TiB steel instead of 20CrMnTi carburized steel to make gears. This is because adding trace boron (0.0001 percent -0.0035 percent ) to structural steel can significantly improve the hardenability of steel. Therefore, adding trace boron to steel can replace a certain amount of precious alloying elements such as manganese, nickel, chromium, and molybdenum. Therefore, boron steel is widely used. Changchun FAW has used 20MnTiB and 20Mn2TiB steels in the production of "Jiefang" brand automobile gears.
The "Dongfeng" brand 5 produced by Dongfeng Motor Company is made of 20CrMnTi and 20MnVB steels respectively for the transmission and rear axle gears of trucks. Similarly, an agreement was signed with steel mills to narrow the steel hardenability band and supply it in stages. The steel for the main and driven bevel gears of the transmission and rear axle are 20CrMnTiH(3) and 20MnVBH(2), 20MnVBH(3), and the corresponding hardenability is J9=32-39HRC and J9=37-44HRC, J9=34. 42HRC.
my country's Qijiang Gear Factory has introduced the German company's heavy-duty automobile transmission gear production technology, and successfully trial-produced the company's Cr-Mn-B series boron-containing gear steel in accordance with German Ⅲ company standards. The hardenability of the gear material is J10=31-39HRC
Spur zobrats
Spur zobrats
Of course, boron{{0}}containing steels such as 20CrMnTi steel, 20MnTiB steel, and 20MVB steel also have shortcomings. It is generally believed that 20CrMnTi and other carburized steels are intrinsically fine-grained steels, and the grains will not be coarsened after carburization and can be quenched directly. But in fact, due to the influence of the quality of steel smelting, grain coarsening often occurs under normal conditions. In the actual grain size test of many batches of materials, it is found that a considerable part of the actual grain size is only 2-3 (under the condition of holding at 930 degree for 3h). The literature believes that due to the high Ti content of 20CrMnTi, there are many TiN inclusions in the steel, especially the large TiN inclusions are the source of fatigue when the gear is fatigued, and its existence will reduce the contact fatigue performance of the gear. This kind of inclusion has a cubic structure and is prone to cleavage and cracking when subjected to force, leading to early failure of the gear. Another problem is that the steel has limited hardenability and cannot meet the requirements of large-diameter and large-modulus gears. The effective hardened layer depth and core hardness of carburizing cannot meet the requirements of heavy-duty gears. In addition, 20CrMnTi steel is prone to internal oxidation and non-martensitic structure during the heat treatment process, which reduces the fatigue life of the gear. However, in my country's gear carburizing steel, there is no steel as mature and reliable as 20CrMnTi steel in the carburizing process. Therefore, it is still the most commonly used carburizing steel in China. Boron steels such as 20MnVB, 20MnTiB and 20Mn2TiB also have some shortcomings. For example, due to poor deoxidation and nitrogen removal during smelting, boron cannot increase the hardenability. Therefore, the performance of boron steel is unstable. After carburizing and quenching The gear distortion increases and affects the quality of the product. At the same time, because the mixed crystals and grains are easy to be coarse, the deformation is difficult to control and the toughness is poor, and the roots of the boron steel gears are prone to produce the troostite structure and the black mesh and black belts of the carbonitriding gears. Therefore, many factories have discontinued the use of this steel. However, it must not be concluded that boron steel is not suitable for gear carburizing steel. Carburized steel containing boron is still used abroad. For example, the famous IV gear factory in Germany has always used the reserved steel grade ZF7 formulated by its own factory, which is a low-carbon chromium-manganese steel containing boron. The main chemical composition (mass fraction, percent ) of the steel is 0.15-0.20C, 0.15-0.40S, 1.0-1.3Cr, 1.0-1.3Mn, 0.001-0.003B. American automobile transmission gears and rear axle main and driven gears are also made of boron-containing carburized steel, such as 50B15, 43BVl4 and 94B17. Therefore, as long as the smelting technology of steel plants keeps up, the above-mentioned problems of boron steel can be solved.
20CrMnTiH, 20MnVBH un 20MnTiBH tērauda zobratu kalšanas sagataves tiek apstrādātas nepārtrauktā izotermiskā normalizācijas krāsnī, lai nodrošinātu vienmērīgu pārslu perlīta un ferīta sadalījumu. Tādā veidā var ievērojami samazināt pārnesuma termiskās apstrādes kropļojumus, uzlabot pārnesuma precizitāti un pagarināt zobrata kalpošanas laiku.
Zobu kalšanas sagatavju izotermiskā normalizējošā cietība ir 156-207HB. 6
Hroma{0}}mangāna-molibdēna tērauds un hroma-molibdēna tērauds
22CrMnMo, 20CrMnMoH un 20CrMoH tēraudi tiek izmantoti vidēja izmēra -automobiļu pārnesumos to augstās rūdāmības dēļ. Šāda veida tēraudu var tieši rūdīt pēc karburizācijas. Tā kā hroma-mangāna-molibdēna tērauds un hroma-molibdēna tērauds satur hromu, molibdēnu un citus elementus, kas veido karbīdus, oglekļa saturs uz zobrata zobu virsmas palielinās. karburēšanas process, un karburizētā slāņa struktūrā, iespējams, parādīsies liels daudzums karbīdu, kas pasliktinās karburizācijas slāņa veiktspēju. Tāpēc, kad zobratu karburizē ar hroma-mangāna-molibdēna tēraudu un hroma-molibdēna tēraudu, ir jāizmanto vāja karburēšanas atmosfēra, lai novērstu pārmērīgu karbīdu veidošanos. 22CrMnMo un 20CrMnMoH zobratu kalšanas sagataves tiek normalizētas un pakļautas rūdīšanai augstā temperatūrā pie 650-670 grādiem. Metalogrāfiskā struktūra ir pārslveida perlīts plus neliels daudzums ferīta, un cietība ir 171-229HB. 20CrMnH zobratu kalšanas sagatavi vislabāk var apstrādāt nepārtrauktā izotermiskā normalizācijas krāsnī, karsējot līdz 935-945 grādiem, iepriekš atdzesējot līdz 640-650 grādiem un pēc tam izotermiski, lai iegūtu vienmērīgu ferīta un perlīta struktūru ar cietību 156-207HB. Literatūrā norādīts, ka 20CrMoH tērauda kausēšanas process ir stabils, rūdāmības josla ir šaura un viegli vadāma. Salīdzinot ar 20CrMnTi tērauda zobratu, tam ir mazāk termiskās apstrādes kropļojumu; karburizētajam slānim ir laba un stabila cietība; metalogrāfiskā struktūra, karburēšana un rūdīšana Virsma un serdes cietība var labāk atbilst tehniskajām prasībām; noguruma veiktspēja ir laba, un tā ir vairāk piemērota maza un vidēja moduļa pārnesumiem automašīnās. Visaptveroši ņemot vērā zobratu ekspluatācijas apstākļus, tas ne tikai nodrošina zobratu noguruma kalpošanas laiku, bet arī samazina zobratu termiskās apstrādes deformācijas. Ja to izmanto transmisijas pārnesumu ražošanai, tam ir jābūt J9=30-36HRC, un, ja to izmanto aizmugurējās ass zobratu ražošanai, tam ir jābūt J9=37- 42HRC.
